Skip to main content

Cadillac Catera Power Seats

The exquisite, leather-covered power bucket seats offered by Cadillac for their Catera (a re-badged Opel Omega; the same platform was also later used for the Pontiac GTO) are a great value for the streetrodder. From 1997-2001, about 95,000 were sold in the USA. The leather seats feature 6-way power (driver and passenger; some are heated) and are made by Recaro. These are some of the most comfortable seats I've ever sat in and are frequently sold on eBay for $350 a pair .

Really? Just $350 for a pair of such nice seats? Why are they so relatively inexpensive?

The passenger seat is a conventional power seat with conventional relays and wiring. Wire up +12V and a ground and you're good to go. But the driver's seat uses solid-state relays and is connected to the car's main computer. As a result, many people believe that the seat won't work unless it's installed in a Catera and hooked up to the car's main computer. They are wrong.

All you lose by not being connected to the Catera's main computer is the three memorized positions that the main computer can store. Still, many people could not get the seats to work. The secret is all in the wiring, but the solution is hidden in the Troubleshooting section of the Cadillac service manual.

First, there are three +12V connections: two thicker wires and a thin wire. The thicker red ones (#1 & #3 in the service manual) are connected to an always-powered source. The thinner red one (#4) is connected to an accessory-powered source. The brown wires (#2 and #5) are the grounds. The data control wire is #6 and is not used. The secret wire is #7, a thin grey wire. In the Catera, this is connected to the door switch that controls the courtesy lights. When this wire is not grounded (when the door is open), the seats will not move. I just grounded it permanently; it seems the GM engineers did not want you to move the seat with the doors open. It's also important to wire #4 to a circuit that is hot only when the engine is running or it will drain the battery. That's all there is to it.

There are only two drawbacks to these seats. First, the Catera was four-door car, so these seats will not fold forward. If you used them in a two-door car, you won't have access to the rear seats. Second, they are wide, so without some modification to the seat cushion and re-covering, they are not usable in most 30's-vintage cars.

But if they fit (or can be made to fit), you will have some sweet, comfortable Recaro 6-way power seats for your ride for just $350.

WIRING INFORMATION
For wiring information, visit your local Cadillac dealership, explain what you are doing and ask to see their service manual for the year of manufacturer of the car the seats came from. Then find the technician diagnosis section for the power seats. That's how I found the info for may seats.

Comments

Unknown said…
i have a pair of these i just picked up for 25$ at you pull it.. they have side air bags and i am wondering if they are the same as yours.. i am going to look at the wiring the next time get in the garage to see if they have the same wires..
April 30, 2011 at 7:57 PM
Cowboyprotectionunit said…
Same here...... I'm looking at the wiring here and I'm not seeing some of the same wiring..... any tips....I Just Blew Something On the inside.... with like a retaining cap...... sounded like a gunshot.... I'm thinking a Safety Restraint
September 6, 2011 at 12:32 PM
Route 60 Garage said…
Mine don't have side air bags. You can look at wiring diagrams by going to the dealership and asking to see their service manual. I found the info I needed in the troubleshooting part.
January 22, 2012 at 9:05 PM
omex18 said…
Im installing this seats on my 94 silverado where do i wire #1,#3 can i wire #4 to power window fuse
November 25, 2013 at 9:32 PM
Post a Comment

Popular posts from this blog

WTF is a Franzinator?

Sometimes the most useful things have the oddest names. Take the Franzinator, for instance. Named after Franz©, its curmudgeonly inventor, the Franzinator is a device used to separate moisture from compressed air. Having moisture in compressed air is not a a good thing, especially in painting where it contaminates the painted surface, or in media blasting where it causes the media to clump and not work as well. As well as causing rust in the air tanks and air tools, moisture is best removed. A number of methods have been developed from expensive refrigerated driers used to pre-condition air before it gets to the compressor, to simple mechanical separators that sit in the air line between the tanks and the air tool. Here is a tank that uses a chemical desiccant to dry the air. There are also ways to install the air lines that are intended to either cause moisture to condense or collect before it is sent to the air tool. A non-mechanical separator causes the moisture in the hotte...
Post a Comment
Read more

O-Ringing the Block and Heads for Higher Compression Engines HOWTO

I found some useful advice in this forum thread from user AK's REX. "To my understanding o-ringing the block or the head prove to be about equally effective. That said I would say it depends if you want to have receiver grooves machined. The most conventional method is to machine and o-ring the block, then machine receiver grooves opposite the o-rings in the heads. I guess it can probably be done in reverse fashion as well. As far as the receiver grooves are concerned, it not only helps in high compression and or boosted applications, but helps wet motors from losing fluid which is a common problem with copper head gaskets. It allows the o-ring to literally push the gasket into the receiver groove to provide a better seal. Speaking of copper gaskets here is a bit of info from SCE regarding this stuff; O-ring grooves may be cut in either the block or cylinder head. When using copper head gaskets thinner than .050, O-ring height should be no more than 25% of gasket thickness...
Post a Comment
Read more

Retrofit Hydroboost Brakes

Traditional power brakes have used engine vacuum to reduce the physical effort required to stop a car. Some high performance engines, because of the design of their camshafts, do not produce enough vacuum to used vacuum-powered brake power boosters. One alternative is to add a vacuum pump to the accessories driven by the engine. Another is to use the hydraulic pressure supplied by the power steering pump to power the brake booster. This device is called Hydroboost and it replaces the vacuum-operated brake booster. It provides more than twice the pressure than a vacuum diaphragm booster. There are commercial kits to use a hydraulic booster, like Vanco . They offer kits to match the car you are modifying. The most complete kits provide the Hydroboost unit, a new master brake cylinder, a power steering pump and the appropriate hoses with fittings and they are priced at around $900. You can see the parts of the kit by visiting this link . A nice step-by-step installation of the Vanco h...
Post a Comment
Read more