Skip to main content

Cadillac Catera Power Seats

The exquisite, leather-covered power bucket seats offered by Cadillac for their Catera (a re-badged Opel Omega; the same platform was also later used for the Pontiac GTO) are a great value for the streetrodder. From 1997-2001, about 95,000 were sold in the USA. The leather seats feature 6-way power (driver and passenger; some are heated) and are made by Recaro. These are some of the most comfortable seats I've ever sat in and are frequently sold on eBay for $350 a pair .

Really? Just $350 for a pair of such nice seats? Why are they so relatively inexpensive?

The passenger seat is a conventional power seat with conventional relays and wiring. Wire up +12V and a ground and you're good to go. But the driver's seat uses solid-state relays and is connected to the car's main computer. As a result, many people believe that the seat won't work unless it's installed in a Catera and hooked up to the car's main computer. They are wrong.

All you lose by not being connected to the Catera's main computer is the three memorized positions that the main computer can store. Still, many people could not get the seats to work. The secret is all in the wiring, but the solution is hidden in the Troubleshooting section of the Cadillac service manual.

First, there are three +12V connections: two thicker wires and a thin wire. The thicker red ones (#1 & #3 in the service manual) are connected to an always-powered source. The thinner red one (#4) is connected to an accessory-powered source. The brown wires (#2 and #5) are the grounds. The data control wire is #6 and is not used. The secret wire is #7, a thin grey wire. In the Catera, this is connected to the door switch that controls the courtesy lights. When this wire is not grounded (when the door is open), the seats will not move. I just grounded it permanently; it seems the GM engineers did not want you to move the seat with the doors open. It's also important to wire #4 to a circuit that is hot only when the engine is running or it will drain the battery. That's all there is to it.

There are only two drawbacks to these seats. First, the Catera was four-door car, so these seats will not fold forward. If you used them in a two-door car, you won't have access to the rear seats. Second, they are wide, so without some modification to the seat cushion and re-covering, they are not usable in most 30's-vintage cars.

But if they fit (or can be made to fit), you will have some sweet, comfortable Recaro 6-way power seats for your ride for just $350.

WIRING INFORMATION
For wiring information, visit your local Cadillac dealership, explain what you are doing and ask to see their service manual for the year of manufacturer of the car the seats came from. Then find the technician diagnosis section for the power seats. That's how I found the info for may seats.

Comments

Unknown said…
i have a pair of these i just picked up for 25$ at you pull it.. they have side air bags and i am wondering if they are the same as yours.. i am going to look at the wiring the next time get in the garage to see if they have the same wires..
Same here...... I'm looking at the wiring here and I'm not seeing some of the same wiring..... any tips....I Just Blew Something On the inside.... with like a retaining cap...... sounded like a gunshot.... I'm thinking a Safety Restraint
Route 60 Garage said…
Mine don't have side air bags. You can look at wiring diagrams by going to the dealership and asking to see their service manual. I found the info I needed in the troubleshooting part.
omex18 said…
Im installing this seats on my 94 silverado where do i wire #1,#3 can i wire #4 to power window fuse

Popular posts from this blog

A Heat Insulation Spray-on Coating Alternative to Lizard Skin.

One of the well-known spray-on heat-shield products is Lizard Skin. From their website, “LizardSkin Ceramic Insulation (CI) is an advanced spray on thermal coating that consists of a water-based composition of high-grade acrylic binders with ceramic insulation particles to create a thermal barrier.” The Material Safety Data Sheet (commonly referred to as the MSDS) can be found here . This sheet shows the composition of Lizard Skin as: 1 - Water 7732-18-5 40-50% 2 - Resin Polymer 00-00-00 20-30% 3 - Trade Secret Insulation Media 10-20% 4 - Carbon Black 1333-86-4 5-10% 5 - Extender Pigment 1317-65-3 1-5% It’s relatively expensive at $200 for two gallons. They sell a special gun ($120) to spray it on although it can be applied with a brush or roller. Substitutes It's possible to make your own for much less cost. 1 – High solids white latex ceiling paint. 2 - Acrylic Polymer Resin - increases paint flow and durability. One source is Acri-Flow

WTF is a Franzinator?

Sometimes the most useful things have the oddest names. Take the Franzinator, for instance. Named after Franz©, its curmudgeonly inventor, the Franzinator is a device used to separate moisture from compressed air. Having moisture in compressed air is not a a good thing, especially in painting where it contaminates the painted surface, or in media blasting where it causes the media to clump and not work as well. As well as causing rust in the air tanks and air tools, moisture is best removed. A number of methods have been developed from expensive refrigerated driers used to pre-condition air before it gets to the compressor, to simple mechanical separators that sit in the air line between the tanks and the air tool. Here is a tank that uses a chemical desiccant to dry the air. There are also ways to install the air lines that are intended to either cause moisture to condense or collect before it is sent to the air tool. A non-mechanical separator causes the moisture in the hotte

Keeping Your Compressor Quiet

Air compressors are noisy machines. The two most commonly used ways to quiet them down are to locate the air intake outside (not good for the neighbors) or to build some type of enclosure with sound deadening material inside; that usually causes overheating problems due to poor circulation. The best solution is to construct a silencer that uses the same principles as a gun silencer. But isn't that illegal? Only if you use it on a gun. We're using it on an air compressor. Still, this topic seems to be controversial, mostly by people who have a bury-your-head-in-the-sand approach to security and safety. Here are the materials: Pipe the same size the air compressor port will use, 16"-18" long. Some exhaust pipe, the same length as the other pipe. Some washers you have to make with a hole saw, enough to put one on each end and one every 1-1/2" that will fit around the air compressor intake port pipe and fit inside the exhaust pipe. Steel wool to fit betwe